Zeoseal

Porous

line

Zeoseal Porous is a water base, clear, VOC-free, non-flammable, water-repellent primer & sealer to treat all high-absorbent cement surfaces such as concrete, plaster, brick or absorbent tiles & stone from the back side prior to fixing on floor and wall as well from the top before final use.

Available in

WEIGHT
  • 05

    LTR

  • 01

    LTR

  • 00

    LTR

COLOR

  • check

PACK

  • check

  • check

  • check

Zeoseal Porous
Product Coverage Calculation
Download Technical Datasheet

Advantage of Zeoseal Porous

ASTM C97 / C97 – M-09Zeoseal Porous

Wallnut Zeoseal Porous is a unique Eco-friendly (very low VOC) water-raw material to provide excellent resistance & ingress against water, water stain, rising dampness in brick & efflorescence when used either as a primer on the back side of absorbent tiles or stone before fixing or as a sealer coat over absorbent granite or marble or on cement-based surfaces such as concrete, plaster, brick etc.

Zeoseal Porous is ready to use and when applied, it creates water drop effects and is most suitable for products such as clay tiles, terracotta floor tiles, sandstone, absorbent granite or gypsum-based surface.

Suitable for interior & exterior areas

Zeoseal Porous Hi-Tech Features

Wallnut Waterproof
Low Voc
  • Excellent water beading effects for a long time.
  • Guaranteed protection against water, efflorescence, alkali and chlorides (soluble salt etc.)
  • Very low VOC (Low Volatile Organic Compound) and suitable for green building point
Wallnut High-performance technology
  • A long-life assurance of performance
  • High-performance - Zeoseal Porous ensures that absorbent mineral surfaces are fully protected against the ingress of water.

Best Suitable Areas for Zeaseal Porous

Residential & commercial buildings
Kitchen countertops & Bathrooms
Industrial buildings and chemical resistance areas such as laboratory, Industrial kitchen, staircase, etc
Public infrastructures such as railways, airports, stadiums, bridges, etc.
swimming pools deck areas, Jacuzzi & saunas  public uses.
Operating areas like Dado, Lifts, Areas with heavy public movement

How to Use Zeoseal Porous

Suitable Surface
Suitable areas
Surface Preparation
Mixing
How to apply

  • Absorbent exposed new or old concrete or plaster.

  • Absorbent natural stone such as sandstone or similar pre-polish or post-polish.

  • The back side of tiles, sandstone, brick, granite and marble as a primer coat before fixing with adhesive or mortar.

  • Gypsum base surfaces.

  • Pre-grouting in tiles or stone joints.

  • Internal & external mineral-based absorbent floor & wall surfaces.

  • Residential & commercial buildings.

  • Industrial facilities.

  • Public infrastructure such as airports, railways etc.

  • Ensure that concrete, plaster, tiles, stone or any other mineral substrate is fully dry, clean and free from all foreign materials such as oil, grease, dust etc.

  • The old or new surface can be cleaned by a suitable method such as sandblasting, water blasting or chemical cleaning.

  • When using Zeoseal Porous over absorbent granite and marble as a protective coat, ensure that final polishing is done. When applied as a pre-polished protection coat, further coating will be needed post-polishing.

  • When applied back side of tiles or stone as a primer the back surface must be clean.

  • When applied over mineral / cement-based grout, the grout surface must be cleaned with a suitable cleaner.

  • The temperature of surface must be over 5° C. and less than 40° centigrade.

  • Zeoseal Porous is ready to use a sealer and no further dilution require.

A.) Application as back coat primer on tiles or stone:

  • Once the back surface of the tiles or stone is dry and fully clean, apply the liquid with a sponge or suitable brush on the entire surface and saturate enough for sufficient penetration. The quantity of application is depending on the absorption of the surface and once the first coat is dry after 30-minute a second coat can be applied if needed.
  • The applied surface can be left over for a minimum of 12 hours for the final cure.
  •  

B.) Application as protection coat on absorbent or polished surfaces:

  • Ensure that the final surface is clean and fully dry before starting the application.
  • Apply enough to wet the entire surface with a dry white sponge or with a spray gun for a large area.
  • Once the first coat has been absorbed fully into the surface and if needed second coat can be applied the same way as the first. Allow the final coat to penetrate for 10 minutes and in the case of polished stone, wipe out excess sealer with a dry cotton cloth by buffing technique.

    • In case excess sealer is dried and could not be wiped from polished surface, then second coat application over affected

      area can be done and surface can be buffed.

Keep in Touch

Get in touch for business and product acquisitions enquiries.

For Enquiries
91-22-49713322
91-9967007783

Email
info@wallnut.co.in

 

Web Enquiry
wallnut footer