Metapoxy Grout

First, check that tiles or stones are fixed properly and are not sounding hollow. In case sounding hollow, the first repair or replace the area.
Ensure that joints are clean and free from all foreign material such as oil, grease, dust etc. In case the dust or cement particles are stuck inside the joint, use a vacuum cleaner or blower to remove the same. The Grout remover tool also can be used in case old grout needs to be removed.

In case working in an external area under the sun, avoid applying grout on the hot surfaces and in joints. First, let cool the surface of tiles or stone and don’t work under direct sun. A hot surface may compromise the final performance of grout.
In case the surface of tiles or stone are absorbent, then before starting the application, first apply the grout in a small test patch area. In case of discolouration of surface, apply first Zeoseal Porous Sealer or consult Wallnut technical representative.

In case tiles or stone are rustic in nature and have uneven surfaces, it is possible that grout residue may remain on the surface and be difficult to fully clean. In this case, better not to apply grout on the entire surface area. Also, if needed, edges of tiles or stone can be masked by applying suitable masking tape and can be removed post cleaning of grouts.

Mixing Ratio: Part A-Hardener: Part B-Color resin paste: (1: 15)

Mix part A and part B full quantity in any plastic bucket by using a slow-speed electric stirrer. Mix until smooth & uniform paste is obtained for application.
In case part quantity of grout is mixed, it is advisable to use strictly the correct ratio of Part A-hardener & Part B-resin color paste (1:15). For taking the correct ratio of hardener, a measurement jar or hardener bottle cap can be used. (In case of Part A mixing ratio are not correct, the final result may vary and grout performance can be compromised.)

Use the mixed material within 15 to 45 minutes (Depends on ambient temperature) before it starts setting in the bucket.

Before applying the grout on the overall surface of tiles or stone, test the small area for any discolouration due to absorbency in tiles or stone surfaces.

In case tiles or stone surface is rough or uneven, it is advisable to apply the grout only in the joints and not on the entire surface of tiles or stone to avoid cleaning issues. (A good masking tape also can be used if needed on the edges.) Spread the grout evenly on the surface of tiles or stone to cover the area.

Once the grout is spread, fill the joint completely using wallnut rubber grout float. Keep the rubber float diagonally to the joint and apply a 45-degree angle to have a perfect filling.
Once all the joints are filled properly, remove excess grout if any from the surface of tiles or stone.

To achieve flush joints, leave the grout approx. 30 to 45 minutes (Depending on temperature) in the joints. (Immediate cleaning of grout is possible, but it may lead to uneven grout surface finish).

Pour clean water over the tile or stone surface enough to wet the area and start cleaning the grout with a medium density sponge in a circular motion all over the joints. Finish the joint smoothly and evenly. (Change the water once or twice to have proper cleaning of surface). The sponge cleaning will ensure the grout leaves a smooth and glossy finish at the joints.

Leave the grout for 24 hrs. to dry and fully set. Protect the area for any possible stain on fresh grout due to movement or dust.

After 24 hrs. the tile surface can be cleaned with soap water to remove any haze or traces of colour remaining at the top.

• Advance technology glass beads epoxy grout requires a very short time for mixing and application.

• User friendly 2 component formulation and cleaning can be done in a short time with water only.

• Finger touch smooth finish and shiny joints as per gloss of tiles or stone surface.

• Fully flush joints or concavity is possible based on the application technique.

• Highly suitable for all types of Ceramic, Vitrified & Glass mosaic surfaces.

• Saves time and labour significantly compare to 3 component grouts.

• Highly thixotropic in nature and does not sag from the joint up to 15 mm. or even more.

• Very low VOC (Volatile Organic Compound) and at par with international norms.

• Post application no acid or special cleaner requires to clean the grout surface except normal water.

• Hygiene, antibacterial & does not allow fungal growth by itself.

• The maximum particle size is 250 μm.

• It is able to lock grout colours between joints permanently.

• High-quality UV stable colours in 23 shades.

• No stain on grout joints post-application in everyday use.

• High chemical & stain resistance.

• Almost waterproof by its nature.

• Very high compressive and abrasion resistance.

• Durable and long-lasting.